歡迎進入東莞市渝升五金機械有限公司網站!
東莞市渝升五金機械有限公司
10年沖床生產經驗
沖床穩定、安全、耐用、節能
渝升阿里店鋪
服務熱線:0769-8671-1655
產品分類
4新聞中心
您的位置:首頁  ->  新聞中心

自動沖床操作要求


自動沖床的操作要求

1、操作人員首先應了解機器的結構、性能和技術參數;絕對不允許超負荷使用,待壓工件的變形力一定要小于機器的公稱壓力。模具不許偏裝,工件不許偏壓裁。

2、壓力機附近要收拾整潔,在機器上不得有散亂的毛坯料和廢料、碎屑。壓力機附近其周圍與工作無關的物體必須收拾干凈,并將原材料與半成品擺放整齊。

3、開機前,應檢查沖壓機有無異常狀況,如各機構裝置包括離合器、制動器、剎車系統、腳踏板等是否正常,磨擦部分及潤滑部分有無磨損現象,油杯灌滿潤滑油。

4、檢查沖模和配合部分是否符合技術要求。安裝沖模并調整后可試壓一個工件,檢查是否合格,然后再正式工作。

5、脫開離合器后才可以開動電機,然后再開動機器。如果按下啟動按鈕電機不轉,應立即按下停止按鈕,以防燒毀電機。

6、做數次空程試驗以檢查制動離合器、操縱器各部分有無故障,是否動作可靠。電機達到額定轉速再開動壓力機。



 

 
點圖進入相冊
10T自動沖床.適合加工各種小五金產品
      1, the operator should first understand the structure of the machine, performance and technical parameters; absolutely not allowed to overload the use of the deformation of the workpiece to be pressure force must be smaller than the nominal pressure machine. Mold allowed partial loading, the workpiece not allowed to bias cut.
     2, press in the vicinity to pick up clean, the machine may not have scattered rough material and waste, debris. Press around the vicinity of work-related objects to be cleaned and neatly placed in raw materials and semi-finished products.
     3, pre-boot, stamping machines should be checked whether the abnormal conditions, such as the installation of various agencies, including clutch, brakes, brake systems, pedal board is normal, friction and lubrication part of the availability of some wear and tear, oil cup filled with lubricant.
    4, check whether the part of die and co meet the technical requirements. Install and adjust the die pressure test after a piece to check eligibility, and then formal job.
    5, disengaged the clutch can be switched on only after the motor, and then switch on the machine. If you press the start button motor does not turn, should immediately press the stop button, to prevent burning of motors.
    6, do a number of air-way test to check the brake clutch, whether the various parts of the manipulator failures, whether the action reliably. Motor to achieve rated speed and then activate the press.
 
[返回]   
掃描二維碼
  • 掃一掃進入手機網站
    進入手機網站
    掃一掃關注微信公眾號
    關注微信公眾號
  • 0769-8671-1655東莞市企石鎮東平舊圍路口斜對面
    電話:13433005018
    聯系人:劉先生
  • 東莞市渝升五金機械有限公司 Copyright ? 2019 版權所有 訪問量: 技術支持【東莞網站建設】【Bmap】【Gmap】【后臺管理】 【百度統計 備案號:粵ICP備11043831號
    二八杠正网